In Belgium, every new or heavily renovated home must have controlled ventilation under standard <strong>NBN D 50-001</strong> and the EPB/PEB rules of its region. So the real question is not whether to ventilate but which system to pick. Here is how to choose between single-flow (systems A, B, C) and balanced double-flow (system D) without sizing errors.
Quick answer
Choose according to the building, not fashion:
- <strong>Very well insulated, airtight new build</strong>: balanced ventilation (system D) is usually the most consistent choice.
- <strong>Renovation with no room for ducts</strong>: a well-sized system C with mechanical extraction remains a serious choice.
- <strong>In both cases</strong>: flow rates are calculated room by room under NBN D 50-001, and the installation must be measured and balanced at commissioning.
- <strong>Only system D</strong> is double-flow.
The four ventilation systems in the standard
NBN D 50-001 sorts residential ventilation into four systems, depending on how air is supplied and extracted.
- <strong>System A</strong>: natural. Supply through grilles in dry rooms, extraction through natural ducts in wet rooms. No fan, so airflows are hard to control.
- <strong>System B</strong>: mechanical supply, natural extraction. Rare in housing.
- <strong>System C</strong>: natural supply through grilles, <strong>mechanical extraction</strong> in kitchen, bathroom, toilet and utility room. The most common single-flow system.
- <strong>System D</strong>: mechanical supply and extraction, with a heat exchanger recovering heat from the extracted air. This is the only true <strong>double-flow (balanced)</strong> system.
Design flow rates: the principle of the standard
The standard starts from rooms, not building volume. Dry rooms (living room, bedrooms, office) receive fresh air; wet rooms (kitchen, bathroom, toilet, utility room) extract it. Total flow is sized so air travels through the home from the former to the latter. Reference values for a dwelling:
- Living room: <strong>3.6 m³/h per m²</strong> of floor area, minimum 75 m³/h, nominal flow can be capped at 150 m³/h.
- Bedroom, office, playroom: 3.6 m³/h per m², minimum 25 m³/h, can be capped at 75 m³/h.
- Closed kitchen, bathroom, utility room: 3.6 m³/h per m², minimum 50 m³/h, can be capped at 75 m³/h.
- Kitchen open to other spaces: minimum 75 m³/h.
- Toilet: 25 m³/h.
Single flow or double flow: what changes, and the efficiency to expect
System C is simple, cheap to maintain and very reliable. Its drawback: fresh air enters cold through the grilles, and the heat of the extracted air is lost outdoors. Balanced ventilation filters incoming air, pre-heats it through the exchanger and removes the need for grilles in window frames, which helps with outdoor noise and pollen.
In return it needs an airtight building, room for the unit and two duct networks, and regular maintenance. In a poorly insulated or leaky home, heat recovery loses much of its value.
For heat recovery, do not rely on a brochure figure without conditions. The quoted efficiency is measured under standardised conditions; in practice duct leaks, flow imbalance and defrosting reduce it. Ask for the test conditions.
Good thermal efficiency is not enough: power-hungry fans cancel part of the gain. The EU ecodesign (1253/2014) and energy labelling (1254/2014) regulations cover residential ventilation units: compare the energy class and power input.
- <strong>Low-energy or passive new build</strong>: balanced ventilation is usually the consistent choice, since heating demand is low and ventilation losses weigh heavily.
- <strong>Renovation</strong>: balanced ventilation only makes sense if ducts can be routed (loft, dropped ceilings, shafts) and airtightness addressed. Otherwise a well-tuned system C is an honest solution.
- <strong>Apartment</strong>: the constraint is often the shared shaft and noise level; decentralised units exist.
Filters, maintenance, condensate, frost and summer
A balanced system needs attention on several technical points:
- <strong>Filters</strong>: A coarse filter on extraction and a finer one on incoming air are common. Follow the manufacturer's replacement and cleaning interval.
- <strong>Condensate</strong>: cooling the extracted air produces water. It needs a drain to a trap with a proper slope, and the unit must sit in a frost-free place.
- <strong>Frost protection</strong>: in severe cold the exchanger can ice up. The unit handles this with a pre-heater or a temporary reduction of supply flow.
- <strong>Summer bypass</strong>: in summer the bypass avoids warming incoming air, and allows night ventilation with cooler air. It does not replace solar shading.
- <strong>Access</strong>: the unit must stay reachable for maintenance without dismantling anything.
Ducts, noise and commissioning
The duct network largely determines comfort. Undersized ducts force high air speeds, hence noise and pressure loss. Aim for short, straight, generously sized ducts, with silencers on branches to bedrooms and preferably inside the heated volume.
Terminals must sweep the whole home: supply in living room and bedrooms, extraction in wet rooms. Commissioning with flow measurement and balancing is essential; without it, nothing that was calculated is actually delivered.
Common mistakes
- Choosing balanced ventilation without tackling the building's airtightness.
- Undersizing ducts or using too many bends.
- Forgetting transfer openings (door undercuts) between dry and wet rooms.
- Connecting the cooker hood to the ventilation network instead of using a recirculating hood or a dedicated extract.
- Not balancing the flows at commissioning.
- Neglecting maintenance: clogged filters, falling flows, rising noise.
- Ignoring regional EPB/PEB requirements at design stage.
What to check before buying
Before signing, ask the manufacturer and installer for these items:
- The room-by-room flow calculation under NBN D 50-001.
- The test conditions of the heat recovery efficiency and the energy class on the EU label.
- The filter type, replacement interval and availability.
- The sound level of the unit and the terminals, room by room.
- The presence of a bypass, frost protection and a condensate drain.
- Access to the unit for maintenance.
- The commissioning report with measured flows, and your region's requirements (Service public de Wallonie, Brussels Environment, Vlaams Energie- en Klimaatagentschap).
Frequently asked questions
What is the difference between single-flow and double-flow ventilation?
Single flow extracts stale air mechanically and lets fresh air in through grilles. Double flow (system D) supplies and extracts air mechanically and recovers heat from the extracted air to pre-heat the incoming air.
Which systems does NBN D 50-001 distinguish?
Four: A (natural), B (mechanical supply), C (mechanical extraction) and D (mechanical supply and extraction). Only D is double-flow.
What heat recovery efficiency is realistic?
Brochure figures are measured under standardised conditions; in a real installation duct leaks, flow imbalance and defrosting reduce them. Ask for the test conditions and compare the energy class.
Can balanced ventilation be installed in a renovation?
Yes, if ducts can be routed properly and airtightness is adequate. Otherwise a well-sized system C remains a serious option.
How often should filters be changed?
Per the manufacturer's manual and the environment (busy road, pollen, building works). Clogged filters cut flow and raise consumption.


